Milliput Silvergrey ,
Two Parts Epoxy putty 113,4g
Using Milliput - A two part epoxy putty
Milliput is the trade name for our epoxy putty. We produce five grades: Standard (Yellow/Grey), Terracotta, Silver Grey, Black and Superfine White. Each grade is presented in similar packs containing 2 x 56•7gm. sticks and the general instructions for preparation and usage are the same.
Once equal quantities of each stick have been mixed the resultant putty is at first soft and highly adhesive and then gradually hardens. Speed of hardening is dependant on temperature and at normal temperatures (20-25 deg C) Milliput becomes rock hard in three to four hours. By the application of heat the setting time can be reduced.
After setting hard Milliput continues to cure and is fully cured after an elapse of time equal to the setting time at the same temperature. Once fully cured Milliput can be machined, drilled, tapped, turned, filed, sawn, sandpapered and painted.
Milliput is an excellent adhesive and will bond any of the following to itself or to any of the others - wood, brick, cement, metals, concrete, plastics, glass etc, but note that Milliput is not intended as a thin layer adhesive. Milliput will set under water and is heat resistant up to 130°C.
Mix together equal parts of each stick from the pack. Knead and roll in the hands for at least 5 minutes until the colours merge and become uniform and no streaks can be seen, and then mix for another minute. The surfaces to which the putty is applied should be free from grease and dirt. Smooth surfaces should be cleaned with a suitable solvent or with soap and warm water to remove dirt and grease. Abrading the surface will improve adhesion. the putty may now be applied and will set hard in three to four hours without shrinking.
At all stages from initial mixing to final setting Milliput responds to the use of water. To aid manipulation and avoid sticking, fingers and tools should be kept moistened with water. There are certain instances when work may be carried out in a gentle stream of water under a tap. To obtain a smooth finish, mould or apply Milliput and then immediately wipe and smooth gently with wet finger or with a fine textured moist cloth.
When tools have been used for applying or contouring Milliput they should be cleaned immediately after use. If the putty is allowed to harden on it will be almost impossible to remove.
In the putty state Milliput, like most chemicals in domestic use, may cause irritation to sensitive skins. When mixing the two components it is advisable to use rubber gloves or throw-away polythene gloves. When rubber gloves have been used wash them immediately after use, and whilst still on the hands, using running water. If the hands have been used for mixing or manipulating Milliput wash them immediately after use with toilet soap and warm water.
When casting or mouldmaking talc or a light oil can be used as a releasing agent.
Milliput products are resistant to frost, heat, solvents and most fuels.
This product is compatible with:
 |
GREEN STUFF Kneadatite9,50 EUR (19 % VAT incl. excl. Shipping costs) |
Customers who bought this product also bought the following products:
 |
35;Heads without headgear10,50 EUR (19 % VAT incl. excl. Shipping costs) |
 |
35;Heads without headgear10,50 EUR (19 % VAT incl. excl. Shipping costs) |
 |
Bohrersatz 0,3 - 1,2mm (20 Stk)5,99 EUR (19 % VAT incl. excl. Shipping costs) |
 |
Brünierungsmittel für Metall (Messingketten,-Antennen, Rohre etc.) 50g (Preis /100g =135,00 Euro6,75 EUR (19 % VAT incl. excl. Shipping costs) |
 |
Gunze Masking Fluid 25ml (Preis /1L 180,-- Euro)4,50 EUR (19 % VAT incl. excl. Shipping costs) |
 |
Sprühkleber 200ml (1l = 49,95 Euro)9,99 EUR (19 % VAT incl. excl. Shipping costs) |
